#Fldigi rigcat xml files manual
#Fldigi rigcat xml files full
#Fldigi rigcat xml files windows

Pity, if as appears the case, we can't make use of this very handy feature. Doesn't explain why it wasn't visible at all with your version though Terry? I appears therefore that 'Hamlib' must be enabled for this feature to work and is the reason why I guess that it's greyed out when LOG4OM is linked with XML-RPC.

#Fldigi rigcat xml files windows

Mentor assistance is available on the following online forums groups.io: linuxham - primarily for Linux and OS X users nbems - support for using the entire suite in an EMCOMM environment all operating systems win-fldigi - Windows users The file sha256vals.txt contains the sha256 checksum value. Very fast and very convenient! If you do not have hamlib enabled for your transceiver this button will be dimmed and not activated. Please send all trouble reports to or one of the online support groups. The tranceiver frequency will be shifted and the fldigi audio tracking point shifted in unison such that the signal is now at the receivers sweet spot. Let the AFC capture and then press the QSY button. let's say that I just started copying a rare dx at 1758 Hz and I wanted to put the signal at the sweet spot so I could easily narrow the receiver bandwidth. As the transceivers bandwidth is changed the changes occur centered at this frequency. Each rig has a sweet spot associated with its bandwidth controller. The QSY button is very specific to rigs interfaced with either hamlib or the memory mapped i/o.

#Fldigi rigcat xml files manual

Terry, FYI, and others following this thread I've just looked at the FLDIGI Users manual (should have done so before my previous post), it confirms what I was saying. So in conclusion its working fine within the constraints of the FLDigi parameters when using the XML-RPC interface with Log4OM, the only issues I found were FLDigi shortcomings and these are beyond our control and not a Log4om issue. But it also might be the case when the width of the main dialog is reduced so that the waterfall display does not extend over the entire available width. This is usually the case when the X2 or X4 expansion is selected.

#Fldigi rigcat xml files full

NOTE: these controls are only functional if the current waterfall or spectrum view is smaller than the full view available. Then I read the manual for FLDigi and found this note:

I found that the 'Centre the signal' button on the bottom tool bar did not function with the waterfall set to x1, functioned partially with Waterfall set to x2 and worked perfectly when set to x4 XML-RPC control activated in Fldigi with Hardware PTT, RigCat and Hamlib disabled (Not selected)įLDigi 'Sweet Spot' set to CW 700, RTTY 2200 & PSK et al 1500 Very impressed with these current programs.OK I have just checked this out and my set up is as follows I have never used SOUND card modes before, I always used HARDWARE. The 991 RF gain I use to control the waterfall blue yellow issues. Go into the Computer Control Panel and find the. This is where I set CW, RTTY, and packet modes.Īs you change these modes the lower LEFT corner will reflect the change. you are using RigCat or flrig, you will need the XML description file for your radio. It worked for me.ĭATA-USB is set under the freq readout on FLDIGI I keep it set to that for everything.įLDIGI SCREEN under the freq readout there is a option: OP MODE. If you save this frequency to a memory, the DATA-USB Mode and the function selections will all be saved.ĭisclaimer: it was on original write up. ( turn off the MONI if you wish.) I like it on. This should show a blue background on the FLDIGI waterfall from about 200 to 3000 HZ. ( this will also be used in receive mode for fine adjustments.) The MULT knob until the width reads 3000HZ. Now move the options buttons until you find the WIDTH button. Shift the options buttons until you find NAR/WIDE button. Adjusting the RF GAIN will be used a lot during receive. ( you may use the DT gain for fine level corrections during operation. Then select the ALC meter and press the DT GAIN button and adjust the MULTI KNOB for no ALC indication. Using the Windows Mixer for Playback Device, turn down the USB AUDIO CODEC playback slider to show 50 watts on the 991 power meter. ON FLDIGI, Push the tune button (upper right hand corner of window). Hit the 991 F button, shift through function option and set MONI to on. Turn up the 991 RF gain control, then use the WINDOWS mixer record control the USB AUDIO CODEC to turn down the waterfall shows mostly blue with some yellow noise spots. Should be in DATA-USB or it will not transmit. Set the 991 mode to DATA-USB using either the FLDIGI RIG MODE select box or Se lect OP Mode at top of FLDIGI screen to RTTY.